Resin Pathways

Guide · Homeowners · 4 min read · Updated 17 November 2026

Can Resin Be Laid Over Concrete or Tarmac? What to Check

Short answer

Yes, resin bound can be laid over existing concrete or tarmac if the surface is sound, stable, free of significant cracks or movement and drains properly. The surface is cleaned, repaired and primed, then a 15–18mm resin layer is laid. In the UK this typically costs £45–£70 per m², compared with £85–£130 per m² for a path with a new base.

Can Resin Be Laid Over Concrete or Tarmac? What to Check

Why overlaying is popular

Laying resin over an existing path avoids digging it out, taking away the waste and building a new base. That saves time, mess and money, often halving the cost per square metre. For many homeowners with a tired but solid concrete or tarmac path, an overlay transforms its appearance in a day or two.

The catch is that the resin layer is thin, typically 15–18mm, and relies entirely on what is underneath. If the base moves, cracks or breaks up, the resin will follow. That is why a careful assessment of the existing surface is the most important part of the job.

What makes a base suitable

A suitable base is solid, stable and has been in place long enough to have settled. Concrete should be free of significant cracks, heave or sunken sections, and should not rock or sound hollow when tapped. Tarmac should be firm, not crumbling or loose at the surface, and should not soften in hot weather. Both should drain properly, without puddles sitting on the surface after rain.

CheckGood signWarning sign
CracksNone or fine hairline cracksWide, moving or stepped cracks
StabilitySolid, no rocking slabsSunken or lifting sections
SurfaceFirm and cleanCrumbling tarmac, loose aggregate
DrainageWater runs offPuddles after rain
LevelsGood falls away from houseFalls towards the house

How the overlay is done

First, the existing surface is cleaned thoroughly to remove dirt, moss, algae, oil and loose material, because resin will not bond to a dirty surface. Cracks are repaired, and movement joints in concrete are dealt with, as resin laid straight over a joint will crack along it. Edging may be fitted where there is no hard edge to contain the resin.

A primer is then applied to help the resin bond to the base. The resin and aggregate are mixed in batches, spread and trowelled to a smooth finish across the path. The surface is usually walkable within hours and fully cured within a day or two, depending on the weather.

Weather plays a big part on the day. Resin should not be laid in rain or on a damp surface, and very low or very high temperatures affect how it cures. Installers watch the forecast closely and may move the date if conditions are not right. Allow time for the surface to dry thoroughly after cleaning before the primer goes down.

  • Clean off dirt, moss, oil and loose material
  • Repair cracks and deal with movement joints
  • Fit edging where needed
  • Apply primer
  • Mix, spread and trowel the resin layer
  • Leave to cure before use

The problem of reflective cracking

Reflective cracking is when cracks in the base show through the new resin surface. It happens when the old concrete or tarmac moves, whether through temperature changes, settlement or tree roots. Fine hairline cracks that are stable can often be repaired and overlaid, but wide or active cracks are a sign that the base is still moving.

Concrete with expansion joints needs particular care. If resin is laid continuously over the joint, the movement will crack the resin along that line. Installers usually carry the joint through the resin or use a crack-bridging approach where appropriate.

Tree roots deserve a special mention. Paths near trees can be lifted and cracked as roots grow, and a resin overlay will not stop this. If roots have already lifted the path, an overlay is likely to crack again in the same place. A new base, sometimes with root barriers or a different route, gives a longer-lasting result.

Drainage when overlaying

Resin bound is permeable, but when it is laid over solid concrete, water passes through the resin and then meets an impermeable layer. It must run off along the surface of the concrete, so the existing falls need to carry water away from the house. Resin laid over solid concrete is not permeable in itself, so drainage must be designed to take water away rather than towards the house or road.

For front gardens, this matters for planning. In England, laying more than 5 square metres of hard surface in a front garden needs planning permission unless it is permeable or drains to a lawn or border. An overlay on solid concrete may need to drain to a border or soakaway.

When a new base is the better option

If the existing path is badly cracked, sunken, crumbling or falls towards the house, overlaying is a false economy. The resin will crack or fail and you will pay twice. In that case, digging out and building a new permeable base is the better long-term choice, typically £85–£130 per m² including excavation, membrane, sub-base, porous binder course, edging and resin.

Old slabs and block paving are generally not suitable for overlaying either, because individual units move independently.

Thresholds and levels are another reason to rebuild. An overlay adds height, typically 15–18mm plus any primer, which can bring the surface too close to door thresholds and damp-proof courses. Paths should finish comfortably below the damp-proof course so water does not bridge into the walls. If the existing path is already close to that level, digging out and lowering the base is often the right answer.

Getting the right advice

Because so much depends on the condition of the base, an honest site assessment is essential. Be wary of anyone who quotes for an overlay without looking closely at cracks and levels. Through us, you can request quotes from vetted, insured local resin specialists who will tell you whether your existing surface is suitable or needs rebuilding.

Questions people also ask

Can resin be laid over block paving?

Generally not. Block paving and slabs are made of individual units that move slightly, and that movement will crack a thin resin layer. In most cases the paving is lifted and a suitable base is built, or the resin goes on a new porous binder course.

How thick is a resin bound overlay?

For paths, a resin bound layer is usually around 15–18mm thick, depending on the aggregate size. Driveways that take vehicles need a thicker layer. The thickness should be stated in the quote, as laying it too thin is a common cause of failure.

Will cracks in my concrete show through resin?

They can. Stable hairline cracks can usually be repaired before overlaying, but wide or moving cracks are likely to reappear through the resin, known as reflective cracking. If the concrete is still moving, a new base is usually the better option.

Written and checked by the Resin Pathways team. Read our editorial policy.

Get a free resin pathways quote

Tell us what you need and we'll come back with a clear price.

Request a quote